Author(s)

Zhangui Wang ¹, Jie Yang ¹

Affiliation(s)

¹ Ningxia Tiandi Northwest Coal Meachine Limited Company, Shizuishan, 753000, China

Corresponding Author

Zhangui Wang

ABSTRACT

In modern industrial production, belt conveyor is essential, its advantage is that it can save a lot of manpower and material resources. Belt conveyor accessories are more, the structure is complex, the complexity of the drum and the technical difficulty is higher. As we all know, the roller plays a great role in the belt conveyor, and its performance also determines the overall performance of the belt conveyor. There are many kinds of rollers on the market today. Because it carries a large number of different angles of force and friction, the loss is relatively large. In this paper, the drum structure is introduced first, and the expansion joint structure is selected as the research object. Then, the friction transmission principle between the drum and the belt is analyzed, and the variation of the envelope Angle and tension is calculated. Finally, the simulation results show that the acceleration of the improved drum is 0.1ms2 less than that before the improvement, indicating that the proposed research is helpful to the optimization of the belt conveyor drum.

KEYWORDS

Belt conveyor; A roller; Belt; Friction force; Tension change

CITE THIS PAPER

Zhangui Wang, Jie Yang, Structural optimization and modal analysis of belt conveyor driving drum. Journal of Engineering Mechanics and Machinery (2024) Vol. 9: 81-86. DOI: http://dx.doi.org/10.23977/jemm.2024.090113.

REFERENCES

[1] Bajda, M., & Hardygóra, M. (2021). Analysis of the Influence of the Type of Belt on the Energy Consumption of Transport Processes in a Belt Conveyor. Energies, 14(19), 6180.
[2] Alharbi, F., Luo, S., Zhang, H., Shaukat, K., Yang, G., Wheeler, C. A., & Chen, Z. (2023). A brief review of acoustic and vibration signal-based fault detection for belt conveyor idlers using machine learning models. Sensors, 23(4), 1902.
[3] Hrabovský, L., Blata, J., Hrabec, L., & Fries, J. (2023). The detection of forces acting on conveyor rollers of a laboratory device simulating the vertical section of a Sandwich Belt Conveyor. Measurement, 207, 112376.
[4] Auezova, A., Buzauova, T., Abdugaliyeva, G., Kurmangalieva, L., Smagulova, N., & Zhauyt, A. (2020). Investigation of the stress-strain state of the roller conveyor. Metalurgija, 59(2), 199-202.
[5] Hao, Y., & Liu, Q. (2023, December). Design and Research of Improved Tail Hydraulic Tension Belt Conveyor. In Proceedings of the 2023 International Conference on Intelligent Sensing and Industrial Automation (pp. 1-6).
[6] Liu, J., Qin, H., Wang, G., & Zhao, H. (2021). Control algorithm of permanent magnet direct drive belt conveyor system for mining based on reduced order model. International journal of pattern recognition and artificial intelligence, 35(14), 2159052.
[7] Feng, Y., Zhang, M., Li, G., & Meng, G. (2020). Dynamic characteristic analysis and startup optimization design of an intermediate drive belt conveyor with non-uniform load. Science Progress, 103(1), 0036850419881089.
[8] Wang, M., Shen, K., Tai, C., Zhang, Q., Yang, Z., & Guo, C. (2023). Research on fault diagnosis system for belt conveyor based on internet of things and the LightGBM model. Plos one, 18(3), e0277352.
[9] Wang, X., Ding, G., Cheng, Z., Surucu, G., Wang, X. L., & Yang, T. (2020). Novel topological nodal lines and exotic drum-head-like surface states in synthesized CsCl-type binary alloy TiOs. Journal of Advanced Research, 22, 137-144.
[10] Chen, P., Han, Y., Jia, F., Meng, X., Xiao, Y., & Bai, S. (2021). DEM simulations and experiments investigating the influence of feeding plate angle in a rubber-roll paddy grain huller. Biosystems Engineering, 201, 23-41.
[11] Kong, X., Tang, J., Hu, Z., Ding, H., Wang, Z., & Wang, Q. (2023). Dynamic modeling and vibration analysis of spur gear system considering thin-walled gear and hollow shaft. Mechanism and Machine Theory, 181, 105197.
[12] Jaiswal, S., Sopanen, J., & Mikkola, A. (2021). Efficiency comparison of various friction models of a hydraulic cylinder in the framework of multibody system dynamics, Nonlinear Dynamics, 104(4), 3497-3515.
[13] Salawu, G., Bright, G., & Onunka, C. (2020). Modelling and simulation of a conveyor belt system for optimal productivity. International Journal of Mechanical Engineering and Technology (IJMET), 1(11), 115-121.

Sponsors, Associates, and Links

---

• Cybernetics and Mechatronics
  
  
• Digital Manufacturing and Process Management
  
  
• Ultra-Precision Machining Process
  
  
• Journal of Robotics and Biomimetics
  
  
• Prognostics, Diagnostics and Health Management
  
  
• Micro-Electro-Mechanical Systems
  
  
• Journal of Precision Instrument and Machinery
  
  
• Engineering and Solid Mechanics
  
  
• Fracture and Damage Mechanics
  
  
• Frontiers in Tribology
  
  
• Fluid and Power Machinery
  
  
• Chemical Process Equipment
  
  
• Journal of Assembly and Manufacturing
  
  
• Mechanical Vibration and Noise